Quantcast
Channel: ABN Newswire
Viewing all 12706 articles
Browse latest View live

Investigator Resources Ltd (ASX:IVR) Paris Preliminary Metallurgical Results

$
0
0
Investigator Resources Limited (ASX:IVR) provides an update on the progress on metallurgical results carried out as part of the Pre-Feasibility Study ('PFS') on the Company's Paris Silver Project.

The preliminary metallurgical results indicate that:

- Cyanide leach trials achieved weighted average silver recoveries around 74% with a range of 65% to 89% for the three main geometallurgical domains.

Additional scrubbing, flotation and mineralogical tests are continuing, aimed at recovering lead and more of the non-leaching silver.

These metallurgical results aim to enable the design and costing of a process flowsheet.

Investigator's Managing Director John Anderson said "The results reported by the metallur-gical consultants are consistent with 2013 testwork but require some further investigation to augment silver recovery and bring the processing options to a logical conclusion. This is expected to be reported in June 2018. The metallurgical performance of the Paris silver deposit is seminal in the decision to bring the Project into production and is worthy of the critical attention being applied to its' resolution."

The project lies within the Peterlumbo tenement on the northern Eyre Peninsula of South Australia (Figure1). The Paris silver deposit has an estimated Indicated and Inferred JORC Mineral Resource of 9.3 million tonnes at 139g/t silver and 0.6% lead (at a 50g/t silver cut-off) (Investigator ASX Release: 19 April 2017). The deposit occupies an area of about 400m by 1,600m with a shallow flat tabular geometry that is conceptually mineable by open-pit to 160m depth below the flat surface.

As announced previously (Investigator ASX Release: 21 October 2013), the results of initial standard metallurgical laboratory tests for the Paris Silver Project showed metallurgical performance in labora-tory trials conducive to conventional processing paths. The initial silver leach recoveries were in the range 65% to 75% for the samples of breccia mineralisation typical of most of the Paris deposit.

Metallurgical Investigations for the PFS

Following the release of the Paris Silver Mineral Resource estimate in April 2017, Investigator com-menced a phased PFS study with a central focus on metallurgical performance. An extended geomet-allurgical study of the geologically complex Paris deposit enabled the selection of four domains (Oxide; Breccia transitional - no Mg/Ca; Breccia transitional - Mg/Ca; and Dolomite) (Figure 2) for metallurgical testing of larger and more representative samples (Investigator ASX Release: 14 November 2017). The study is again being undertaken by the metallurgical testing and process engineering/flowsheet Company, Core Resources ("Core") in Brisbane.

Comminution testing showed that the Paris silver ore can be considered 'soft' and has relative low abrasive properties. This indicates potentially lower capital and power costs associated with the crushing and milling circuit (Investigator ASX Release: 14 November 2017).

In the 2018 study, Core has carried out flotation and leaching testwork, evaluating options for further improving silver recoveries, as well as identifying methods to recover lead/silver concentrate which was not examined in 2013.

Multiple mineralogical studies including scanning electron microscope work identified the main silver species as acanthite (silver sulphide - the most common globally mined silver mineral), chlorargy-rite/bromargyrite (silver chloride & bromide) and primary native silver. All species identified are gen-erally less than 30 microns in grainsize, and mostly less than 10 microns. The lead minerals are pre-dominantly galena (lead sulphide), laurionite (lead chloride) and coronadite (lead manganese oxide).

Grinding of the breccia ores to P80 of 53 microns (80% passing 53 microns) enabled 65% to 85% silver leach recoveries (Table A) by cyanide leaching with lead nitrate or hydrogen peroxide pre-condition-ing. The Dolomite domain returned 89% silver leach recoveries without pre-conditioning. The Oxide domain has performed poorly in leach trials thus far and, as this domain only hosts 5% of the resource it is discounted from the PFS. The balance of the silver that remained unleached is referred to as refractory silver. Ultra-fine grinding to 10 microns achieved improved silver recoveries in similar leach trials, but is unlikely to be an economic pathway.

Flotation and gravity tests were undertaken to assess the recovery of lead in concentrates along with some of the refractory silver in the Breccia Transitional (no Mg/Ca) domain. These tests produced concentrates with poor lead recoveries of approximately 8% in a flotation concentrate and 24% in a gravity (Knelson) concentrate. The unrecovered lead is attributed to the coronadite content and fine galena inclusions in quartz.

Additional scrubbing tests are being completed aimed at rejecting gangue minerals ahead of leaching. Additional flotation tests are investigating options for further upgrading of the silver and lead concen-trates.

Mineralogical studies have thus far identified very fine-grained native silver inclusions in quartz as one of the refractory silver species. On-going scanning electron microscopy is seeking further avenues to optimise the silver recovery.

Core will prepare a process flowsheet, mass and water balance/model, process description and a final process report for inclusion in the PFS in June 2018.

The Company is considering further testwork using CELP (CANMET Enhanced Leaching Process) tech-nology.

Other work towards the Paris Pre-Feasibility Study

Geotechnical, waste characterisation and infrastructure costing studies are on-going and will be re-ported as final reports are received. The completion of the metallurgical and geotechnical studies will enable the Company to make a decision on the future of the Project.

To view tables and figures, please visit:
http://abnnewswire.net/lnk/2M5L8G23

Mr John Anderson
Managing Director
Investigator Resources Limited
info@investres.com.au
Phone: 08 7325 2222

Mr Peter Taylor
Investor Relations
NWR Communications
peter@nwrcommunications.com.au
Phone: 041 203 6231

Speedcast International Ltd (ASX:SDA) Completion of 7 year US term loan refinancing

$
0
0
Speedcast International Limited (ASX:SDA) (FRA:7SC), the world's most trusted provider of remote communication and IT services, today announced the pricing of its US$425 million Senior Secured Credit Facility (the "Term Loan") in the US institutional Term Loan B market with participation by key global financial institutions. The Term Loan has a term of 7 years and a coupon of LIBOR + 2.50%. In addition, Speedcast has arranged a new 5-year US$100 million Senior Secured Revolving Credit Facility.

Proceeds of the new facilities will be used to refinance Speedcast's existing bank loans, which include a 3-year US$425 million Senior Secured Bank Loan and a US$20 million Senior Secured Revolving Credit Facility. The new facilities will diversify Speedcast's funding sources, extend its debt maturity profile and improve the company's operational flexibility in the future.

Credit Suisse (Left Lead), Citi, Crédit Agricole, ING and Macquarie acted as Joint Lead Arrangers and Joint Bookrunners.

"This refinancing transaction builds and broadens Speedcast's relationships with lenders, accessing a range of major financial institutions in the US Term Loan B market. It also demonstrates our disciplined approach to funding through a proactive early refinancing that increases capital flexibility at attractive terms," said Clive Cuthell, Chief Financial Officer, Speedcast.

Key terms of the Term Loan agreement follow:

 
Term             Description  
Facility Size    US$425 million
Term             7 years
Coupon           LIBOR + 2.50%
Early repayment  At Speedcast's option
Use of Proceeds  Refinance existing bank loans

Public Relations and Marketing:

Toni Lee Rudnicki
Vice President, Global Marketing
Speedcast International Ltd
E: tonilee.rudnicki@speedcast.com
T: +1-832-668-2634

Investors:

Ian Baldwin
Chief Financial Officer
Speedcast International Ltd
E: Ian.Baldwin@speedcast.com
T: +61-2-9086-2785

Rumble Resources Ltd (ASX:RTR) First Order Conductor Identified at Munarra Gully Project

$
0
0
Rumble Resources Ltd (ASX:RTR) ("Rumble" or "the Company") is pleased to provide an update on the scheduled drill program at the Munarra Gully Cu-Au Project (with Ni - Co potential) ("Munarra Gully") some 50km NNE of the town of Cue within the Murchison Goldfields.

Highlights

- A large first order conductor has been defined by a moving loop transient electromagnetic survey conducted over the White Rose Cu-Au Prospect.

o The conductor lies 600m west along strike from the open cut workings where historic drilling has returned high-order intercepts including:

-- 40m @ 0.66% Cu, 4.85 g/t Au from surface to end of hole.

- inc 8m @ 1.32% Cu, 22.75 g/t Au from 24m.

o The parameters of the conductor have been modelled as a WNW dipping plate measuring 470m by 260m with a conductance of 650 siemens which is in line with disseminated to semi-massive pyrite - chalcopyrite mineralisation. Depth to the top of the plate is estimated at 120m.

- RC drilling is planned to test both the conductor and significant copper-gold mineralisation associated with the White Rose Prospect.

White Rose Prospect - M51/122 and E51/1677

Background:

The White Rose Prospect is a mineralised ultramafic intrusion that runs from east to west which hosts two open cuts where shallow historic RAB drilling has defined exceptional copper-gold mineralisation that is completely open along strike and at depth:

- 40m @ 0.66% Cu, 4.85 g/t Au from surface to end of hole.

o inc 8m @ 1.32% Cu, 22.75 g/t Au from 24m.

- 20m @ 0.54% Cu, 1.52 g/t Au from surface to end of hole.

Over the last 8 to 10 years, the current owner established a small gold plant (ball mill and Knelson concentrator) to process shallow saprolitic (oxide) gold mineralisation defined by the previous RAB drilling. No official gold production is known however during the 1980's an extensive alluvial gold operation covered most of M51/122 with a reported production of "12,300t of surface alluvium producing 234 oz of gold" (refer to recent announcement 27 February - JORC table for Open File reference). Base metals were not targeted.

The owner developed two small open cuts (down to 20m) which exposed a weathered (nontronite-talc saprolite) ultramafic intrusion at least 50m in width. The ultramafic unit did not surface and was covered by alluvium and hardpan which masked the copper anomalism.

Grab sampling completed by Rumble and others identified consistent copper, gold, nickel and cobalt in weathered ultramafic rocks exposed in the two small pits (currently being mined for gold). Results include:

- An average of 0.68% Cu for all 33 samples collected (max Cu value 2.1%).

- Au to 1.9 g/t.

- Ni to 0.37% and

- Co to 0.11%.

Rumble considers the copper-nickel bearing ultramafic unit at the White Rose Prospect to be highly prospective for disseminated to massive copper +/- nickel sulphide mineralisation. Rumble is currently earning into the Munarra Gully Project as per acquisition terms outlined in ASX announcement 27 February 2018.

MLTEM Survey - White Rose Prospect - M51/122 and E51/1677 - Image 1 and 2 in link below.

A ground moving-loop transient electromagnetics (MLTEM) survey was conducted at the White Rose Prospect targeting semi to massive copper and/or nickel sulphide conductors associated with an ultramafic intrusion that has returned significant copper-gold mineralisation and elevated nickel-cobalt.

A significant conductor has been identified 600m to the west of two small open pits (White Rose Prospect) and has been interpreted to be the western extension of the prospective ultramafic intrusion. Modelling of the conductor has highlighted a 470m by 260m conductive plate (mid-time channels 17.9 - 59.6ms) dipping to the WNW (dip at 54deg). The top of the conductor is estimated to be around 120m deep.

Important: The parameters and conductance (650 siemens) of the conductor is what would be expected from pyrite/chalcopyrite disseminated to semi-massive sulphides. The conductor is considered a first order base metal target based on the wide significant copper and gold mineralisation from historic drilling and significant base metal and gold results from rock chips associated with the ultramafic intrusion.

Proposed Drill Targets (Image 1 and 2 in link below)

Conductor

- RC drilling will target the top third of the modelled conductive plate.

- Subject to results and downhole TEM modelling, further drilling is planned.

White Rose Au-Cu Pits

- Two RC drill-holes will test beneath the two small open cuts targeting the strong copper - gold mineralisation associated with the ultramafic intrusion.

Subject to receipt of relevant approvals that are currently pending, it is anticipated that the drilling will be conducted late May.

To view tables and figures, please visit:
http://abnnewswire.net/lnk/MP0J3WN9

Shane Sikora
Managing Director
Email: enquiries@rumbleresources.com.au
Phone: +61-8-6555-3980
Website: www.rumbleresources.com.au

Core Exploration Ltd (ASX:CXO) Placement to Yahua to Advance Finniss Lithium Project

$
0
0
Emerging Australian lithium developer, Core Exploration Ltd (ASX:CXO) ("Core" or the "Company") is pleased to announce that it has entered into a binding Subscription Agreement with Ya Hua International Investment and Development Co. Ltd ("Yahua"), which is wholly owned by Sichuan Yahua Industrial Group Co. Ltd ("Yahua Group"), one of China's largest lithium hydroxide and carbonate producers, for a placement of $1.4 million to Yahua ("Placement"). This Placement is in addition to the initial $2.0 million placement to Yahua announced on 29 August 2017 and further demonstrates Yahua's support for Core's lithium projects.

HIGHLIGHTS

- Core and Ya Hua International Investment and Development Co. Ltd which is wholly owned by Sichuan Yahua Industrial Group Co., Ltd ("Yahua Group") have executed a Subscription Agreement to increase Yahua's investment in Core;

- Yahua has committed to subscribe for $1.4 million at 5.3 cents per share;

- This Placement is in additional to the previous investment of $2.0 million made by Yahua in 2017;

- Yahua Group is a A$2.4 billion A-share listed company on the Shenzhen Stock Exchange, and is one of China's largest lithium hydroxide and carbonate producers, with significant expansion plans;

- The signing of this Subscription Agreement with Yahua reflects the strong level of interest from potential offtakers and development partners for the high grade spodumene at the Finniss Lithium Project near Darwin, Northern Territory.
The Placement of 26.4 million shares at 5.3 cents per share is on the same terms as the recently announced placement and Share Purchase Plan (refer ASX announcement 16 April 2018). The Share Purchase Plan is scheduled to close at 5pm AEST Tuesday 8th May 2018.

The additional funds raised by this Placement will provide Core with the ability to expand its regional exploration and resource focussed drilling within its Finniss Lithium Project with the ultimate objective to delineate further high grade spodumene resources to support a long-life mining operation capable of producing a high quality spodumene concentrate. Core's 2018 drilling campaigns are expected to commence imminently.

The Placement is expected to be completed within the next week and will be made under the Company's 15% placement capacity (Listing Rule 7.1). Following the Placement, Yahua will hold a 9.7% interest in Core (undiluted for new shares that will be issued upon close of the Share Purchase Plan).

About Sichuan Yahua Industrial Group Co. Ltd

Sichuan Yahua Industrial Group Co. Ltd. is a China-based company principally engaged in the manufacture and distribution of civil explosives. The company is an A-share listed company on the Shenzhen-stock exchange in China, with a market capitalisation of over RMB 13 billion (A$2.4 billion).

Yahua Group is already one of China's largest lithium producers and has significant expansion plans. Yahua Group's existing operations includes a 12,000tpa lithium hydroxide refinery and a 6,000tpa lithium carbonate refinery, and it has plans to expand its production to 50,000tpa of lithium salt production. As a major supplier of lithium salts in China, Yahua Group has long term stable relationships with a number of the large downstream customers of lithium batteries and has broad marketing and distribution channels. Yahua Group already has significant business interests in Australia, including operations in Darwin, where it manufactures explosives for industrial use.

The company's main products include industrial chemical and explosives applied in mining, hydropower, transportation construction, urban renewal, geological exploration and national defence industries. The company is also involved in the provision of engineering blasting solutions and related services, as well as the production and sale of lithium carbonate, lithium hydroxide and other lithium salt products. The company distributes its products in domestic market and to overseas markets.

For further information please contact: 

Stephen Biggins
Managing Director
Core Exploration Ltd
T: +61-8-7324-2987
E: info@coreexploration.com.au 

For Media and Broker queries: 

Andrew Rowell
Director - Investor Relations
Cannings Purple
M: +61-400-466-226
E: arowell@canningspurple.com.au

Altech Chemicals Ltd (ASX:ATC) Company Presentation

$
0
0
Altech Chemicals Ltd (ASX:ATC) provide the latest Company Presentation.

Final Investment Decision Study (FIDS)

- Pre-tax NPV7.5 US$ 505 million

- Internal Rate of Return (IRR) 22%

- Payback (full rate) 3.9 years

- EBITDA US$ 76 million p.a.

- Capital cost US$ 298 million

- Production Costs - US$ 9.90/kg

- LT Sale Price - US$ 26.9/kg

- Gross Margin - 63%

To view the presentation, please visit:
http://abnnewswire.net/lnk/0EMQXJ0S

Iggy Tan
Managing Director
Altech Chemicals Limited
Tel: +61-8-6168-1555
Email: info@altechchemicals.com 

Shane Volk
Company Secretary
Altech Chemicals Limited
Tel: +61-8-6168-1555
Email: info@altechchemicals.com

Investor Relations (Europe)
Kai Hoffmann
Soar Financial Partners
Tel: +49-69-175-548320
Email: hoffmann@soarfinancial.com

Speedcast (ASX:SDA) and Plug and Play Partner to Drive Innovation in the Communications Industry

$
0
0
Speedcast International Limited (ASX:SDA) (FRA:7SC), the world's most trusted provider of remote communication and IT services, and Plug and Play, the world's largest global innovation platform and startup accelerator, announced a strategic partnership focused on the advancement of technology within the communication and IT services sector.

Speedcast's decision to partner with Plug and Play demonstrates the company's commitment to innovation and will accelerate the development of new technologies and business models. The partnership directly links Speedcast with high-potential startups and builds a collaborative environment to focus on technology innovation.

"We are excited about our partnership with Plug and Play, which is the first partnership of its kind in the remote communication and IT services sector," said Tim Bailey, Executive Vice President, Products, Marketing & Business Development, Speedcast. "We are committed to be at the forefront with new technologies that enable us to develop new solutions for our customers. The relationship with Plug and Play helps accelerate Speedcast's innovation capabilities."

Speedcast will join as an Anchor Partner in the Supply Chain & Logistics Program in collaboration with other partners such as CMA CGM, DHL, Lufthansa Cargo, Maersk, Panasonic, and Union Pacific in Silicon Valley. Plug and Play's Supply Chain & Logistics Program will ensure engagement with a select group of startups exploring new ideas and the development of technologies linked to Speedcast´s product roadmap.

"Plug and Play is the ultimate innovation platform, bringing together the best startups and the world's most advanced corporations," said Saeed Amidi, Founder and CEO of Plug and Play. "We are pleased that Speedcast has chosen to partner with us."

About Plug and Play

Plug and Play is a global innovation platform. Headquartered in Silicon Valley, we have built accelerator programs, corporate innovation services, and an in-house VC to make technological advancement progress faster than ever before. Since inception in 2006, our programs have expanded worldwide to include a presence in over 20 locations globally giving startups the necessary resources to succeed in Silicon Valley and beyond. With over 6,000 startups and 220 official corporate partners, we have created the ultimate startup ecosystem in many industries. We provide active investments with 200 leading Silicon Valley VCs, and host more than 700 networking events per year. Companies in our community have raised over $7 billion in funding, with successful portfolio exits including Danger, Dropbox, LendingClub, PayPal, SoundHound, and Zoosk. For more information, visit www.plugandplaytechcenter.com.

Toni Lee Rudnicki 
Vice President, Global Marketing	
Speedcast International Ltd
ToniLee.Rudnicki@Speedcast.com 
+1-832-668-2634

EnviroSuite Limited (ASX:EVS) Thames Water update

$
0
0
Envirosuite Limited (ASX:EVS)(FRA:57P) is pleased to provide an update on its progress with the UK-based water utilities group Thames Water, the UK's largest water and wastewater services company. Thames Water has now committed to an Envirosuite subscription at a fourth site.

Although the individual deal is on standard terms and not material to total company earnings in isolation, it serves to demonstrate the growing relationship between Thames Water and Envirosuite following the third site that was signed only in March 2018. Following an initial commercial trial which completed in mid-2017 at two sites, it is encouraging to see that Thames Water is adopting the Envirosuite platform for the longer term in other parts of the business.

Envirosuite is rapidly establishing its name in the wastewater industry in Europe and the Middle East and now has commercial contracts at seven sites in this region, with a growing number of other similar opportunities in the sales pipeline. Combining the Envirosuite name with the well-established ex-Odotech presence in the North American market means that Envirosuite is emerging as the leading choice for larger wastewater treatment facilities globally.

Peter White, Chief Executive Officer, commented that, "Envirosuite is a natural fit for the wastewater industry. Its major needs for a real-time operational decision-support capability, together with the need to proactively manage its community engagement to ensure an ongoing social licence to operate, are requirements that match the major differentiators for Envirosuite. There are many thousands of waste water sites in our target geographies that could benefit from Envirosuite and we are encouraged by the escalating recognition and uptake of our solution."

EnviroSuite Limited
T: +61-7-3004-6400
E: enquiries@envirosuite.com
WWW: www.envirosuite.com

Blackham Resources Ltd (ASX:BLK) High Grade Oxide & Transitional Mineralisation Identified

$
0
0
Blackham Resources Limited (ASX:BLK) (OTCMKTS:BKHRF), (Blackham or the Company) is pleased to present an update on successful initial drill results from the Wiluna free milling deposits. During March'18 and April'18, Blackham's exploration team drilled 130 RC holes (11,446m) focused on delineating further free milling open pit reserves over the 3.7km's of strike at the Wiluna Mine. Wiluna Mine drilling is expected to conclude in mid-May and resources will be re-estimated at that time.

Highlights

- Latest drilling has identified extensions to shallow oxide and transitional mineralisation with potential for new open pits close to the Wiluna plant

- Potential to substantially extend the free-milling mine life

- East-West Cross Structures - High grade mineralisation defined near surface
16m @ 4.41g/t Au from 2m including 6m @ 9.53g/t 71g*m
18m @ 0.87g/t Au from 29m and 3m @ 7.65g/t Au from 78m
and 4m @ 3.56g/t Au from 86m 53g*m
8m @ 2.03g/t Au from 5m and 14m @ 1.15g/t Au from 78m 32g*m
10m @ 1.48g/t Au from 9m and 7m @ 1.91g/t Au from 31m 28g*m
8m @ 1.40g/t Au from 11m and 6m @ 2.02g/t Au from 23m 27g*m
12m @ 1.79g/t Au from 33m 21g*m

- Starlight - high grade mineralisation starting close surface
4m @ 6.59g/t Au from 85m and 22m @ 3.29g/t Au from 97m 99g*m
6m @ 6.00/t Au from 55m 36g*m
3m @ 7.04/t Au from 17m and 1m @ 9.20g/t Au from 58m 30g*m

- Wiluna Queen & Magazine - broad shallow mineralisation close to surface
7m @ 4.68g/t Au from 48m 33g*m
25m @ 1.14g/t Au from 10m 29g*m
6m @ 4.67g/t Au from 10m 28g*m
2m @ 5.83g/t Au from 50m and 2m @ 6.52g/t Au from 58m 25g*m

- Recent metallurgical testwork confirmed the Wiluna oxide and transitional ores are an attractive feed for the current Wiluna CIL plant with impressive recovered grades

- Wiluna free milling resources and reserves currently being updated

This is a follow up programme on the 77,000m of drilling completed during 2017, which successfully delivered probable reserves of 669,000oz (7.7Mt @ 2.7g/t Au). Resources and reserves within the Wiluna Mine footprint are currently being updated to include the drilling results.

All of the historic open pits at Wiluna were processed through the CIL plant with the exception of the 2007 East pit cut back. Current drilling is focused on free milling ores above the top of fresh rock (generally top 60m) that metallurgical testwork has confirmed are an attractive feed for the Wiluna CIL plant which last quarter produced 20,631oz @ AISC A$1,092/oz.

Pit optimisation studies completed immediately prior to this drilling demonstrate the potential for open pit cutbacks and new open pits to be developed at the Wiluna mine site. The $1,400 and $1,800 shells are similar in extent, which shows open pit mining is expected to be economic at a range of potential gold prices (Figure 1 in link below). These latest drilling results are expected to support substantial increases to open pit resources and reserves within open pits.

The latest testwork confirms the Wiluna oxide and transitional ores are an attractive feed stock for the current operating Wiluna CIL plant. Average leach recoveries on the oxide and transitional ores were 90.8% and 84.3% after 24 hours.

The Blackham management team believes the free milling ores within the existing Wiluna Mine footprint are an attractive feed stock for the currently operating mill and fast-tracking mining approval is likely given the proximity to existing mining footprint.

Close to surface intercepts at East-West and Wiluna Queen (Figure 3 and Figure 4, respectively in link below) highlight the potential for discovering open pit oxide and transitional free-milling resources "under the headframe".

The potential for increased sulphide resources was highlighted by WURC0508 (Figure 5 in link below), which intersected high grade Wiluna shear-style sulphide mineralisation of 22m @ 3.29 g/t Au from 97m down-hole including 2m @ 5.15g/t Au and 3m @ 8.33 g/t Au. These zones show improving grade and thickness of Starlight mineralisation at depth and remain open for follow-up drill testing.

Wiluna Mine final drilling results from outstanding holes are expected by the end of May, with resource and reserve updates to follow. Golden Age underground drilling is ongoing and Lake Way drilling is due to commence this month.

To view tables and figures, please visit:
http://abnnewswire.net/lnk/33Y67779

Milan Jerkovic
Executive Chairman
T: +61-8-9322-6418 

Bryan Dixon 
Managing Director
T: +61-8-9322-6418

Jim Malone
Investor Relations
T: +61-419-537-714

Chantelle O Sullivan
Media Relations
Citadel-MAGNUS
T: +61-8-6160-4902

Intermin Resources Limited (ASX:IRC) Positive Metallurgical Testwork Results from Richmond Vanadium Project

$
0
0
Intermin Resources Limited (ASX:IRC) ("Intermin" or the "Company") and JV partner AXF are pleased to announce positive initial metallurgical testwork results from the Lilyvale prospect area, part of the Richmond vanadium project. The project is located in northwest Queensland and lies on the Flinders Highway and Great Northern railway, 500km west of the Townsville port and 250km east of Mt Isa (see Figure 1 in link below). The project comprises four main prospects (see Figure 2 in link below) in the Richmond and Julia Creek districts covering an area of 1,520km2 with a total Mineral Resource of 2,579Mt grading 0.32% V2O5 at a 0.29% cut-off grade (see Note 4 below).

HIGHLIGHTS

- First pass pre-concentration testwork completed on samples from the Lilyvale prospect area, part of the Richmond vanadium project in northwest Queensland

- Pre-concentration tests aimed at upgrading the run of mine ore utilising gravity, screening and flotation prior to downstream processing

- Test work completed by Beijing General Research Institute of Mining and Metallurgy and the Hunan Research Institute for Nonferrous Metals in China

- Both Institutes account for over 60% of test work conducted on vanadium in China with testwork programs jointly developed using AXF's in-house expertise and the considerable experience of both institutes

- Particle size analysis confirms previous work where 90% of the contained V2O5 reported to the fine size fractions below 43micronm

- Initial two-stage concentration tests resulted in a 1.1% V2O5 grade in 39% of the mass at a 78.4% recovery

- Further testwork underway to optimise the pre-concentration stages with the aim of delivering a 1.5% - 2% V2O5 feed stock at acceptable recovery for downstream processing testwork (see Note 1 below)

- The Lilyvale prospect has an Inferred Mineral Resource (JORC 2012) of 670Mt grading 0.35% V2O5 at a 0.29% cut-off grade (see Note 2 below)

- Lilyvale is the initial development focus and forms part of the greater Richmond project with a Mineral Resource of 2,579Mt grading 0.32% V2O5 at a 0.29% cut-off grade (see Note 2 below)

- The project is subject to an earn-in Joint Venture with AXF Vanadium Pty Ltd ("AXF") whereby AXF can earn 75% by spending $6m by March 2021 (see Note 3 below)

- Infill drilling at the shallow oxide Lilyvale prospect is planned for the September Quarter to upgrade the resource to the Measured and Indicated categories and to provide additional metallurgical samples

Commenting on the results, Intermin Managing Director Mr Jon Price said:

"The first pass results from Lilyvale are extremely encouraging and confirm the historic testwork completed by Intermin over the last decade. To have highly credentialed research institutes in China delivering 78% of the vanadium into 39% of the mass at good grades bodes well for the optimisation testwork now underway."

"We look forward to further results and moving forward with AXF on the downstream processing studies and upgrading the Lilyvale resource. With the soft oxide mineralisation just 4m below surface at Lilyvale, the scale of the project has the potential to compete with any world class vanadium deposit and meet the supply needs of both the steel and emerging energy storage markets."

AXF Vanadium Managing Director Dr Shaun Ren added:

"These initial results have provided us with growing confidence in the project and formed the basis to move to the next stage where we have committed a further A$5m to optimise pre-concentration, commence downstream processing work and develop a pathway to commercial production."

Overview

As announced to the ASX on 19 September 2017, Intermin completed a formal Joint Venture agreement with AXF over the Richmond project. AXF brings considerable technical expertise to the project and has extensive business relationships throughout Southeast Asia.

Details of the agreement between the parties include:

- An earn-in Joint Venture whereby AXF can earn 25% of the project area by spending A$1m within a one year period and maintaining the project in good standing

- AXF to solely contribute to further expenditure of A$5m on the project to earn a further 50% over a three year period, inclusive of the completion of a Feasibility Study on part or all of the project area

- During the sole funding period, AXF will manage the project with direction from the JV committee comprising representatives from both parties

- Upon AXF satisfying the earn-in terms, each party will contribute to ongoing expenditure in accordance with its respective percentages

AXF has now formally committed to the stage 2 expenditure commitment of A$5m over 3 years to March 2021 inclusive of a Feasibility Study on commercial production.

Metallurgical Testwork (see Note 5 below)

In late 2017, AXF collected approximately 1.2 tonnes of vanadium samples from the Lilyvale prospect area for despatch to two research laboratories in China:

- Beijing General Research Institute of Mining and Metallurgy (BGRIMM), a leading institute directly under the Chinese central government providing innovative technology, diversified products and process-orientated engineering services in mineral and material industries worldwide. With ISO 9001 accreditation, the institute provides complete solution integrating R&D, engineering and equipment manufacture.

- Hunan Research Institute for Nonferrous Metals (HRINM), established in 1958, is the first intellectual property-intensive research institute in the Hunan Province focussed on R&D, metal mining, process selection, smelting and new alloys development.

The ore at Lilyvale comprises soft oxidised limestone rich clays from surface to 15m depth where the oil has been leached out and the enrichment of vanadium and other metals including molybdenum, nickel and copper has occurred. The Lilyvale area has the highest grade of the four prospects (see Figure 2 in link below), is closest to surface for simple open cut free dig mining and is amenable to pre-concentration at site to provide a higher grade feedstock with lower mass.

Testwork programs were jointly developed using AXF's in-house expertise and the experience of both institutes with both programs supervised by AXF's senior technical staff. Initial testwork completed during the December and March Quarters focussed on ore pre-concentration of the run of mine ore. Previous testwork completed by Intermin indicated upgrading of the ore could be achieved by physical means.

Ore mineralogy and particle size analysis has shown that over 90% of the vanadium resides in the fine fractions of the ore below 43 microns. Effective separation and removal of the coarse fraction enables concentration of V2O5 and removal of a significant proportion of the calcite that can impact downstream processing and reagent consumption.

The first phase of the testwork involved additional particle size analysis to confirm historic work followed by single stage and 2 stage concentration tests using a combination of screening, gravity and flotation.

Results of the particle size analysis is shown below as Table 1 (see link below).

As can be seen by the table, 89% of the contained metal reports to the -43um size fraction and 84% to the -20um size fraction confirming historic work completed by Intermin.

Representative samples were dried and crushed ahead of the pre-concentration testwork and single stage tests commenced to assess amenability of different physical separation processes including screening, gravity and flotation. This was followed by a two stage process utilising results from the single stage tests.

Table 2 below shows the results of the 2 stage test. (see link below)

The results show that 78% of the vanadium was recovered in to 38% of the original mass at a grade of 1.1% V2O5. This initial work provides a solid basis for further optimisation work to upgrade the run of mine ore by physical separation ahead of downstream processing.

Next Steps

Optimisation work is now underway to further improve the initial results ahead of downstream processing testwork using proven but commercially sensitive and proprietary technology. This optimisation work is expected to be completed in the September Quarter of 2018. Further updates will be released in the December Quarter where the results do not conflict with confidentiality agreements. Infill drilling at Lilyvale is planned for the September Quarter to upgrade the resource and provide additional samples for ongoing testwork.

Lilyvale Prospect

Lilyvale is located 20km northwest of the Richmond Township and in close proximity to the Flinders Highway and Great Northern Railway line. The current resource totals 671Mt grading 0.35% vanadium pentoxide, 274g/t molybdic oxide (see Note 6 below) and commercially significant copper and nickel mineralisation (see Figure 4 in link below). The deposit is 10-12m thick, up to 5km wide and over 6km long and is open in all directions. The prospect is hosted within marine sediments and differs significantly from the hard rock titaniferous magnetite deposits.

The mineralisation commences 5m from the surface and, as with all the prospects, occurs in two different facies:

1. Oxidised coarse limestone rich clay unit from surface to 15m depth where the oil has been leached out and enrichment of vanadium and other metals has occurred (see Figure 4 in link below). Previous test work had shown that over 90% of the contained metal lies in the -38micronm size fraction (see Note 7 below)

2. Fresh fine grained carbonate - clay - oil shale unit containing vanadium, molybdenum, nickel, copper and significant oil content of 65-75 litres of oil per tonne of shale (see Note 7 below)

Initial development work will focus on the upper mineralised zone at Lilyvale as it:

- Is the highest grade based on the drilling to date with the mineralisation 4-5m from surface

- Can be mined simply by free dig open cut mining at very low strip ratios

- Is amenable to low cost removal of the coarse fraction via scrubbing, trommelling, screening, cycloning and flotation to produce a high grade intermediate feedstock grading ~1.5% - 2% V2O5. Metallurgical testwork continues at two research Laboratories in China to further assess the optimal upgrade ratios and recoveries. (see Note 6,7 below)

- Has been subject to extensive downstream processing testwork for metal extraction.

- Is close to road and rail infrastructure, ports and Asian markets

Notes:

1 See Forward Looking and Cautionary statement on Pages 6 and 7

2 As announced to the ASX on 20 March 2018

3 As announced to the ASX on 19 September 2017

4 As announced to the ASX on 20 March 2018, see also table and Competent Persons Statement on Page 6

5 As announced to the ASX on 20 March 2018. See also JORC Tables in Appendix One on Page 7

6 See Competent Persons statement and JORC tables on Page 6.

7 As announced to the ASX on 20 March 2018

To view tables and figures, please visit:
http://abnnewswire.net/lnk/3349C9R3

Jon Price 
Managing Director
Tel: +61-8-9386-9534
E: jon.price@intermin.com.au

Michael Vaughan
Media Relations - Fivemark Partners
Tel: +61-422-602-720
E: michael.vaughan@fivemark.com.au

Sayona Mining Ltd (ASX:SYA) Pro Rata Renounceable Entitlement Offer

$
0
0
Sayona Mining Limited (ASX:SYA) (OTCMKTS:DMNXF) ("Sayona" or "Company") has today sent letters to eligible and ineligible shareholders respectively, in accordance with the ASX Listing Rules.

The indicative timetable for the pro rata renounceable entitlement offer is set out below.

Event: Offers announced

Date: 4 May 2018

Event: Lodgement of Prospectus with ASIC
Lodgement of Prospectus and Appendix 3B with ASX

Date: 4 May 2018

Event: Notice sent to Shareholders

Date: 7 May 2018

Event: "Ex" date
Entitlement trading starts

Date: 9 May 2018

Event: Record Date for determining Entitlements
Date: 10 May 2018

Event: Prospectus and personalised Entitlement Forms sent to Eligible Shareholders and Company announces this has been completed
Last day of Entitlement trading on a deferred settlement basis

Date: 15 May 2018

Event: Entitlement trading ends and Securities quoted on a deferred settlement basis

Date: 17 May 2018

Event: Last day to extend the Closing Date

Date: 21 May 2018

Event: Closing Date

Date: 24 May 2018

Event: Notice to ASX of under subscriptions

Date: 29 May 2018

Event: Issue date
Deferred settlement trading ends
Appendix 3B lodged on ASX

Date: 31 May 2018

Event: Normal trading resumes
Quotation of Securities issued under the Offers

Date: 1 June 2018

Subject to the ASX Listing Rules, the Directors reserve the right to vary these dates, including the Closing Date, without prior notice.

To view the release, please visit:
http://abnnewswire.net/lnk/RN14X11L

Paul Crawford
Company Secretary
Phone: +61-7-3369-7058
Email: info@sayonamining.com.au
www.sayonamining.com.au

Investigator Resources Ltd (ASX:IVR) Presentation at RIU Sydney Resources Roundup Conference

$
0
0
Investigator Resources Ltd (ASX:IVR) provides the Company's latest Presentation at RIU Sydney Resources Roundup Conference.

INVESTIGATOR: Silver & copper-gold in the Gawler Craton

Paris Silver Project - Discovered in 2011

- 42Moz contained silver

- Favourable silver grade, open-pit geometry & location

- PFS underway to evaluate development pathways

- Focus on Metallurgy & Geotech work to bring the project to a decision point

- Exploring for extensions & repetitions

Opportunities to use Company IP in new terrains & jurisdictions

- e.g. Emerging OD-aged porphyry belt

IVR: The next three months

Paris silver project: Complete metallurgical & Geotech studies & review project.

Paris satellite targets: Evaluate IP & select drill targets.

Maslins IOCG target: Receive Infill MT results from government; Seek JV partner for drilling.

Cartarpo cobalt copper REE prospect: Surface evaluations for extensions.

Wiawera copper-gold prospects: Secure Native Title Mining Agreement to enable geochemical & geophysical surveys to proceed.

Seeking new discovery & development opportunities

To view the full presentation, please visit:
http://abnnewswire.net/lnk/LOQX752U

Mr John Anderson
Managing Director
Investigator Resources Limited
E: info@investres.com.au
T: +61-8-7325-2222

Mr Peter Taylor
Investor Relations
NWR Communications
E: peter@nwrcommunications.com.au
T: +61-41-203-6231

Emmerson Resources Limited (ASX:ERM) Exploration Update Presentation

$
0
0
Emmerson Resources Limited (ASX:ERM) (OTCMKTS:EMMRF) provides the opportunity to view a video interview by ProactiveInvestors Stocktube with Rob Bills, Managing Director.

To view, please copy the following details into your web browser:
http://www.abnnewswire.net/lnk/CD9223U5

Investor Enquiries:
Mr. Rob Bills
Managing Director & Chief Executive Officer
T: +61-8-9381-7838
E: admin@emmersonresources.com.au
www.emmersonresources.com.au

Blackham Resources Ltd (ASX:BLK) A Dominant Position in Australia's Largest Gold Belt

$
0
0
Blackham Resources Ltd (ASX:BLK) (OTCMKTS:BKHRF) provides the Company's latest presentation titled "A Dominant Position in Australia's Largest Gold Belt".

COMPANY OVERVIEW

- Low risk free milling mine plan targeting 80koz annual production at AISC of A$1,100-1,200/oz (US$855-932/oz)

- Gold production in March 2018 quarter of 20,631oz at AISC of A$1,092/oz (US$848/oz)

- Well funded to undertake continued exploration, with advanced brownfield opportunities to strengthen and lengthen reserves -focussed on building a "rolling" five year free milling mine plan

- Strong operating cash flows targeting a net cash position by the end of 2018

- Board and management strengthened with experienced gold mining professionals

- Outstanding long-term upside from dominant land position and 6.5Moz (65Mt @ 3.1g/t) resource base

COMPELLING INVESTMENT OPPORTUNITY

- Free-milling production plan delivering strong operational cashflow

- Strengthened balance sheet and targeting a net cash position by the end of 2018

- Well funded for exploration program to strengthen and lengthen reserves - multiple targets in multiple mineralised systems

- 1.2Moz reserves

- Dominant land position and 6.5Moz resource provides significant upside potential

- Undervalued in comparison to Australian gold producing peers

To view the full presentation, please visit:
http://abnnewswire.net/lnk/5X7HPDAJ

Milan Jerkovic
Executive Chairman
T: +61-8-9322-6418 

Bryan Dixon 
Managing Director
T: +61-8-9322-6418

Jim Malone
Investor Relations
T: +61-419-537-714

John Gardner 
Media Enquiries
Citadel Magnus
T: +61-8-6160-4901

Core Exploration Ltd (ASX:CXO) Grants Lithium Resource Upgrade Marks Major Step Toward Feasibility

$
0
0
Core Exploration Ltd (ASX:CXO) ("Core" or the "Company") is pleased to announce a Resource upgrade for its Grants Lithium Deposit at the Finniss Lithium Project in the Northern Territory which has more than doubled the size of the Indicated Resource and substantially increased the Resource confidence ahead of Feasibility studies to be completed in 2018.

HIGHLIGHTS

- Core's Grants Lithium Resource upgraded - Indicated Resource has more than doubled in size at same high-grade 1.5% Li2O

- More than half of the Grants Lithium Resource is now Indicated Resource

- Increases confidence in Resource ahead of finalisation of the Pre-Feasibility Studies for mining and production of high grade lithium concentrate, commencing at Grants in 2019

- Grants Lithium Resource is one of the highest grade undeveloped lithium deposits in Australia

- Significant potential to grow Finniss Project Resources as Grants is only one of many lithium rich pegmatites identified within Core's large 400km2 of tenure at Finniss

- Strong newsflow ahead:

o Maiden Resource estimate for BP33 expected later this month

o PFS for development of Grants deposit expected next month

o Upcoming aggressive drilling campaigns targeting substantial resource growth at Finniss in 2018 to commence shortly

o Ongoing discussions with additional potential offtake customers

The Grants Lithium Resource defined comprises 2.0Mt at 1.5% Li2O (see Table 1 in link below) and is one of the highest grade spodumene resources in Australia. Over half of the Grants Lithium Resource is now contained in the Indicated category.

Core is in the final stages of completing a Pre-Feasibility Study ("PFS") for the development of a spodumene concentrate and direct shipping ore operation from the Grants Lithium Deposit and expects to deliver the PFS later this quarter. The Finniss Lithium Project has substantial infrastructure advantages; being close to grid power, gas and rail and within easy trucking distance by sealed road to Darwin Port - Australia's nearest port to Asia.

Core is working with the NT EPA to finalise the terms of reference for an Environmental Impact Assessment (EIA), following which, the Company will prepare and submit a Mining Management Plan (MMP) for the development of the Grants project. Based on the prescribed timeframes for assessment by the NT EPA, Core expects the environmental assessment process to take up to 12 months for the Grants project.

Core also expects to complete a full feasibility for the development of spodumene concentrate production from Grants and potentially other future resources within the Finniss Project, such as that at BP33, in 2018 and is planning to complete regulatory approvals and commence production in 2019. A Maiden Resource estimate for BP33 is expected this month.

Core will also be re-commencing an aggressive exploration drilling campaign soon with the aim of substantially growing the resource base for the Finniss Lithium Project to underpin a long-life lithium mining and production business.

Grants Lithium Resource

The results of the Mineral Resource Estimate are provided in Table 1 and Figure 1 (see link below). The Mineral Resources are reported at a high cut-off of 0.75% Li2O.

Dr Graeme McDonald (BSc PhD MAusIMM) was contracted by Core to undertake the Mineral Resource Estimate for the Grants Lithium Deposit. As part of the preparation of the Resource Estimate, Dr McDonald developed a geological interpretation based on cross sections, generated a 3D geological interpretation from interpreted cross sections, created domain interpretations for lithium, developed a block model of the deposit, undertook a geostatistical analysis of the data and estimated lithium grades.

Dr McDonald's report notes that fresh pegmatite at Grants is composed of coarse spodumene, quartz, albite, microcline and muscovite (in decreasing order of abundance). Spodumene, a lithium bearing pyroxene (LiAl(SiO3)2), is the predominant lithium bearing phase (see Figure 2 in link below) and displays a diagnostic red-pink UV fluorescence. The pegmatite is not strongly zoned, apart from a thin (1-2m) quartz-mica-albite wall facies. Overall the lithium content throughout the pegmatite is remarkably consistent.

Grants has a flat Grade-Tonnage curve at the 1.5% Li2O "sweetspot" for spodumene production (see Figure 3 in link below). A high 0.75% Li2O cut-off grade results in no significant reduction in the contained tonnes, demonstrating the consistent high-grade nature of the Resource.

To view tables and figures, please visit:
http://abnnewswire.net/lnk/E497T9P7

For further information please contact: 

Stephen Biggins
Managing Director
Core Exploration Ltd
T: +61-8-7324-2987
E: info@coreexploration.com.au 

For Media and Broker queries: 

Andrew Rowell
Director - Investor Relations
Cannings Purple
M: +61-400-466-226
E: arowell@canningspurple.com.au

Broken Hill Prospecting Ltd (ASX:BPL) Holds Largest Mineral Sands Position in Murray Basin

$
0
0
Broken Hill Prospecting Ltd (ASX:BPL) (OTCMKTS:BPLNF) announces the Company now holds the largest Mineral Sands tenement position in World-Class Murray Basin.

Four new exploration licenses (EL006583; EL006584; EL006585; EL006614) with a combined area of 4163km2 granted in the Murray Basin, Victoria

- One exploration license (EL6139) granted in South Australia, along strike from Tararra (EL8558) in NSW

- BPL (through subsidiary Murray Basin Minerals Pty Ltd) is firmly established as the largest mineral sands tenement holder in the Murray Basin, with holdings of approximately 7300km2

- Exploration activities have identified multiple high-grade low-tonnage heavy mineral sands strandline deposits to support BPL's mobile mining business model

- In depth technical data compilation, validation and infill drill program design has commenced on the new tenement areas

BPL's Managing Director, Trangie Johnston commented:

"Mineral sands commodity prices continue to perform well, and we are seeing improved financial performance from existing mineral sands producers. The granting of four new exploration tenements with walk up resource targets places the Company in a strong position. We now have the critical mass to accelerate these projects at a time of strong underlying market conditions."

NEW TENEMENTS GRANTED IN VICTORIA AND SOUTH AUSTRALIA

The granting of four new exploration licenses (EL006583; EL006584; EL006585; EL006614) in Victoria marks the expansion of BPL's interest across the broader Murray Basin heavy mineral sands (HMS) province. Each new tenement areas hosts multiple parallel mineralised strandlines which in some instances persist over several kilometres of strike. The tenement areas are favourably located near key infrastructure and are characterised by strandline-type mineralisation encountered in reconnaissance drill traverses. Mineralisation persists up to 15km in strike in some areas with overburden varying between 5-20m in thickness.

The new tenements complement recently acquired holdings (EL8649; EL8650) in the Euston area of NSW. The next stage of BPL's exploration workplan will see the newly-acquired areas undergo historical data validation and geological modelling as applied to the Jaws and Gilligans deposits in NSW. This work led to the estimation of Inferred resources of 113 Mt at 1.8% heavy minerals (MH) (10th August 2017).

An additional tenement (EL6139) has been granted in South Australia. EL6139 contains the Oakbank, Boxwood Dam and Johnsons Dam strandline HMS deposits where preliminary (informal) resource estimates have been undertaken by previous explorers. These potential resource areas are located along strike from mineralisation in the company's NSW tenements including the Tararra strandlines (EL8558).

BPL'S HEAVY MINERAL SANDS BUSINESS MODEL

BPL's exploration and development program in the Murray Basin HMS province commenced in late 2014when extensive technical studies were completed confirming the viability of a low-capex/ low-opex modular mobile mining concept.

The mobile mining process would employ a conventional technique of wet gravity separation followed by dry electrostatic mineral separation. It would use a highly mobile Mining Field Unit (MFU; see Figure 2 in link below) to follow the mining face, and a semi-mobile Primary Concentrator Plant (PCP) (see Figure 3 in link below) to facilitate periodic relocation and minimise the pumping distance from the MFU.

EXPANDING EXPLORATION FOOTPRINT

To support the mobile mining concept, BPL is aiming to establish a sustainable pipeline of high grade, relatively lowtonnage HMS deposits amendable to processing through mobile plant equipment. To this end, BPL has expanded its HMS tenement portfolio to approximately 7,300km2, securing its position as the largest tenement holder in the world-class Murray Basin province.

This ongoing strategic growth is the result of extensive historical data compilation and prospectivity analysis that has equipped the company with a unique proprietary database comprising approximately 60,000 drill holes and 2 million metres of drilling. The database has a replacement value of approximately $100 million in today's terms (drilling and assay only).

The newly-granted tenements include:
 
------------------------------------------------------------------
State             Title            Name               Area (km2) 
------------------------------------------------------------------
Victoria          EL006583         Hopetoun Birchip   1438 
Victoria          EL006584         Hopetoun  
                                   Warracknabeal      1059 
Victoria          EL006585         Ouyen              1021 
Victoria          EL006614         Tyrell Ridge       645 
South Australia   EL6139           Danggali North     998 
------------------------------------------------------------------
To view tables and figures, please visit:
http://abnnewswire.net/lnk/1JKW110N

Broken Hill Prospecting Ltd
T: +61-2-9238-1170
E: info@bhpl.net.au
WWW: www.bhpl.biz

Environmental Clean Technologies Ltd (ASX:ESI) Federal Budget 2018 R&D Incentive Program Changes

$
0
0
Environmental Clean Technologies Limited (ASX:ESI) (ECT or Company) is pleased to provide the following statement regarding provisions within the Federal Budget that impact the business.

R&D Incentive Program Changes

The 2018 Federal Budget released last night proposes changes to the R&D Tax Incentive program that aim to reform the program, targeting integrity and fiscal affordability.

Of particular relevance to ECT are the changes that target companies with turnover less than $20M which propose to:

1) Introduce a $4m annual cap on cash refunds

2) Anchor the rate of off-set to the claimant's income tax rate for the year plus 13.5 percentage points

These changes, scheduled to be implemented on July 1st, 2018, were anticipated by the Company and while they generally represent a reduction in potential incentives for certain companies, these changes are not expected to result in a material change to ECT's ongoing R&D programs or proposed Indian project.

Preparation for these changes has been pro-actively managed through the establishment of the Brevet R&D loan facility and the structure of the Master Project Agreement (MPA) covering the Company's Indian project, of which the details will be announced in due course.

The changes will not come into effect until the fiscal year 2019 hence the current tax year's R&D tax offset refund remains uncapped.

ECT Chairman Glenn Fozard, commented, "The Federal Government's R&D Tax Incentive program has been highly supportive, contributing more than AU$12M to our R&D expenditure since 2011. We expect to continue to receive ongoing support from this targeted program as we develop further innovations across our technology suite.

"Given our experience in this field we were also well prepared for changes of this type, pre-emptively structuring our R&D financing and Indian project to mitigate the impact of such legislative changes."

ECT Finance - Equity Lending Facility (ELF)

The Company is also pleased to advise it has received loan principal repayments of approximately $350,000 from ECT Finance (via ELF participants) and will continue to update shareholders as it receives these principal repayments in the future.

About Coldry

When applied to lignite and some sub-bituminous coals, the Coldry beneficiation process produces a black coal equivalent (BCE) in the form of pellets. Coldry pellets have equal or superior energy value to many black coals and produce lower CO2 emissions than raw lignite.

About MATMOR

The MATMOR process has the potential to revolutionise primary iron making.

MATMOR is a simple, low cost, low emission production technology, utilising the patented MATMOR retort, which enables the use of cheaper feedstocks to produce primary iron.

About the India R&D Project

The India project is aimed at advancing the Company's Coldry and Matmor technologies to demonstration and pilot scale, respectively, on the path to commercial deployment.

ECT has partnered with NLC India Limited and NMDC Limited to jointly fund and execute the project.

NLC India Limited is India's national lignite authority, largest lignite miner and largest lignite-based electricity generator.

NMDC Limited is India's national iron ore authority.

Glenn Fozard
Chairman
Environmental Clean Technologies Ltd
E: info@ectltd.com.au
WWW: www.ectltd.com.au

Core Exploration Ltd (ASX:CXO) Issue of Placement Shares and Options

$
0
0
Core Exploration Limited (ASX:CXO) is pleased to announce that it has issued 26,415,094 fully paid ordinary shares as announced on 7 May 2018. The Company has issued the Shares to Ya Hua International Investment and Development Co. Ltd under a share placement raising $1,400,000 (before costs).

Core has also issued 500,000 unquoted options as consideration for investor relations services to Cannings Purple. The unquoted options have an exercise price of $0.10 and expiry of 9 May 2020 and have been issued under the Company's 15% placement capacity under Listing Rule 7.1.

An Appendix 3B seeking quotation of the shares is attached to this announcement (see link below).

To view the release, please visit:
http://abnnewswire.net/lnk/J6W7PJ02

Jaroslaw (Jarek) Kopias
Company Secretary
Core Exploration Ltd
T: +61-8-7324-2987
E: info@coreexploration.com.au
WWW: www.coreexploration.com.au

Cryptocurrency Exchange Binance.com (CRYPTO:BNB) Lists Bytecoin (CRYPTO:BCN)

$
0
0
Cryptocurrency Exchange Binance.com (CRYPTO:BNB) advise that BCN/BNB (CRYPTO:BCN), BCN/BTC and BCN/ETH trading pairs are now available on Binance for trading. You can start depositing and trading BCN now.

Bytecoin is an open-sourced, private and untraceable cryptocurrency that was started in 2012.

Bytecoin is the first coin that implemented CryptoNote technology as a default aspect to build a project. Launched in 2012, Bytecoin was widely spread in the Dark Net as one of the popular available methods for payment. The main thing that separates Bytecoin from most of the other coins is total anonymity - as soon as your transaction appears on a blockchain, your address can't be viewed by anyone.

Bytecoin is the forefather of all of the anonymous cryptocurrencies based on CryptoNote technology. Here's a list of the tech features and specifications Bytecoin has:

Ring Signatures

A Ring signature is a special type of digital signature that can be created by someone from a group of users, but it is unknown who exactly the signer is. Imagine a letter that is signed by a group of 10 people. You know that one of them signed the letter, but there's no way to identify who it actually was (you may only guess). This introduces the untraceability property, which means that for any Bytecoin payment there is a number of equal probable senders.

Unlinkable Transactions

Unlinkable transactions make the Bytecoin blockchain resistant to being scanned, which means it's possible to see the details of a user's transaction, but no one will know the sender or the recipient.

Stealth Addresses

With stealth addresses it's not possible to know the sender and the recipient because of the outputs associated with certain addresses, moreover, it's impossible to know who belongs to a certain output.

The complexity of the features above makes Bytecoin absolutely unique.

Max Supply: 184,470,000,000 BCN

Circulating Supply: 183,880,632,754 BCN

To view the Whitepaper, please visit:
http://abnnewswire.net/lnk/IJ0ID28V

Binance
E: market@binance.com
WWW: www.binance.com


Bytecoin
E: contact@bytecoin.org
WWW: www.bytecoin.org

Kingston Resources Limited (ASX:KSN) Misima Drilling Commences

$
0
0
Kingston Resources Limited (ASX:KSN) (Kingston or the Company) is pleased to announce that drilling has commenced at the Misima Gold Project. The major diamond drilling campaign is targeting extensions to the existing 2.8Moz gold resource and drill-testing of newly discovered exploration targets at Umuna East Side. Kingston anticipates drilling 10,000m this year. This will be the first gold exploration drilling on Misima for more than 15 years. The arrival of freight barge MV Sea Swallow at Misima in late April was an historic event welcomed by the local community.

Highlights

- Major diamond drilling campaign begins at the Misima Gold Project

- Phase 1 to focus on resource extensions and new exploration targets

- KSN on track to complete earn-in to 70% during Q3 2018

Kingston MD Andrew Corbett commented "We're very excited to be underway with our drilling program. To commence drilling within six months of acquiring Misima is a testament to the Kingston team and a strong demonstration of the support the operation is receiving from the local community. Kingston is thankful for the support from the Misimans who are keen to see the project advancing and have worked with the Company to get drilling started."

To view figures, please visit:
http://abnnewswire.net/lnk/209THMUP

Kingston Resources Limited
T: +61-2-8021-7492
E: info@kingstonresources.com.au
WWW: www.kingstonresources.com.au

MMJ PhytoTech Ltd (ASX:MMJ) Portfolio Update

$
0
0
MMJ PhytoTech Ltd (ASX:MMJ) provides the Company's latest presentation.

Focus for 2018

Recycle capital into new investments

- Recycle capital

o AUD$1.8m unaudited corporate cash position

o Portfolio liquidity events will recycle capital for new investments

- Invest $1m to $5m per new opportunity

o Focusing on Canada, Australia and the United States

o Seeking minority investments

o Targeting emerging cannabis sector leaders across the value chain

- Drive shareholder returns by delivering on the investment objective

To view the full presentation, please visit:
http://abnnewswire.net/lnk/727EM3H0

MMJ PhytoTech Ltd
T: +61-8-9389-3150
E: info@mmjphytotech.com.au
WWW: www.mmjphytotech.com.au
Viewing all 12706 articles
Browse latest View live




Latest Images